Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

new guy seeking assistance
#16

I was just getting ready to post the photos but see you have been successful!
#17

Yup. Now I have a new problem. I bought it. It has two issues. And I don’t know much about this stuff, so forgive my naivety.

The -what I would call the “tensioner” wheel on the turntable has a tiny flat spot on the edge, so it kinda sounds like a metronome in the background when playing a record. Is there a replacement part for something like that?

The other is that can’t get much volume out of the unit at all right now, no sound at all out of the subwoofer, I obviously checked the wiring, but couldn’t find anything suspect. 

So I’m assuming something in the amplifier? All the tubes are lit up, but does that mean they’re all functional?
#18

Hello, check here for a new idler wheel. I've used them for different wheels over the years. They also sell needles and cartridges.
Gary is a good guy to deal with and will help you out.
https://www.thevoiceofmusic.com/
#19

My best guess for low volume and somethings not working well is that the power supplies is dying do to bad filter cap and bypass cap throughout the tuner and amp chassis. If you continue to operate it in this condition it can damage expensive parts and worst case catch fire. Servicing this set is somewhat of a fairly large undertaking as there are probably 20-30 caps to replace some resistors and an alignment to do afterwards. I'm not sure what your skill level is for this sort of thing is but wouldn't catogorize it as an entree level project. No ofence just being honest. You might luck out and may have mostly disk caps rather than the older foil/paper style.

GL.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#20

Thanks for the info. My skill level is not advanced. How much would I pay someone to do something like that? Ballpark?
#21

Don't really know. Depends on who working on it. If there is a radio club, old or ham perhaps there is someone there that is willing to take it on. I would think that this would be more economical that a shop. The flip side is that hobbyist may not be in any hurry to get er done.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#22

There is a Wisconsin Antique Radio Club where you might find someone relatively close to you to work on the set.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 96 cabinet veneer
There is some description of the veneers in the 1930 Brochure in our library. Here's the link: klondike98 — 11:59 PM
Philco 91 Speaker Replacement
I can't remember, but there was a particular product for loosening glue on the more modern "spiders", used pos...MrFixr55 — 09:43 PM
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM

[-]
Who's Online
There are currently 1903 online users. [Complete List]
» 1 Member(s) | 1902 Guest(s)
Avatar

>