Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

double chassis Philco ID
#1

Hi guys, this is a shot in the dark. I saw a Philco radio in an Antique shop, couldn't find the model #. It was a table top radio not a cathedral or a tombstone.
The only thing I can remember was that it had two chassis's. The chassis on the right is smaller and connected to the larger one by a plug like a speaker would be. This is looking from the back.
I wish I had taken picture's of it. Would like a model or models that would have this type of chassis. I believe it is a 1930-40 vintage. Did some searching but no luck...............

Any help would be appreciated .

Jim
Spring Lake MI
#2

Hi Jim,
The only multiple chassis radios Philco built in the 30's would have been the 37-690 and 38-690 consoles. In a table set...possibly what you saw was a farm battery set, with either a power converter (battery eliminator) added, or if it was a 6 or 32 volt set, possibly it was a vibrator power supply.

The only other possibility I can think of in a 1930's table set would possibly be something with the model 4 shortwave converter added...but I believe that only the 470 and 490 consoles had the converter built in to them from the factory. Otherwise the converter was a stand alone unit.
#3

Sorry for the late reply, it is a 38-40T model.

Jim
Spring Lake MI
#4

Hi Jim,
The 38-40T is a 6 volt battery set, with a separate 115 volt power supply in it, so it could be operated on either battery or AC modes. Kinda odd to do it that way, but I have a 6 volt set from Phonola (Canadian brand) that is done that way as well.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 1862 online users. [Complete List]
» 1 Member(s) | 1861 Guest(s)
Avatar

>