Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

AMI E120 jukebox speaker recone
#1

Well I finally got the jukebox playing correctly picking up the records and playing and returning with no hang ups.
Problem was just did not sound real good.
  Since I had rebuilt the amplifier and rewound the output transformer and installed a new cartridge/needle. I decided to give a try at re-coning the 15"
speaker. The cone had some small holes and the outer part was very thin.
https://imgur.com/Mko627V
https://imgur.com/4LFccHs
  I had to order the parts from three different places due to the odd sizes of the voice coil and spider the is glued to a frame of it's own.
https://imgur.com/uqYWuUp
https://imgur.com/bv2KBy7
  Here is the spider and frame that had to be cleaned up and new one glued on.
https://imgur.com/gTLC0nJ
   https://imgur.com/7O6SVn5
  Above pic is the voice coil , spider, and shim in position for the cone. This took a lot of trial fitting to get the voice coil and spider set to the right height.
https://imgur.com/srtfMkh
  Finally complete. I tested it with my audio generator and just an hor ago had it in the jukebox and sounding soooo much better.
https://imgur.com/y7EW1fB
  I'll post some pictures of the jukebox tomorrow.
#2

That is a really nice job Mike Icon_smile

I don't hold with furniture that talks.
#3

Thanks Ed there was way more to it but I tried to just hit the main points of the re cone.
#4

Here is a few pictures of the finished jukebox. I still have cleaning to do on the metal trim.
https://imgur.com/CZGGKdn
https://imgur.com/26OiDDg
https://imgur.com/Z6y705R
https://imgur.com/bBTbeCJ
#5

Great job Mike Icon_thumbup

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5123 online users. [Complete List]
» 1 Member(s) | 5122 Guest(s)
Avatar

>