Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

late 1936 116B Labeling
#1

Hello,
I am just finishing up the restoration on a late 1936 116B.  

   

Here is the cluster of inside case labels:

   


The labeling inside the cabinet contains a label that I had not encountered until this radio - the For Correct Operation label.    It is attached using one staple and is kind of "toasty" and aged.
   

It is 2" X 3 1/8" in size.  Just wondering on what other models this this label / tag used.  From the la
Thanks very much and stay well.
#2

My 116B didn't have much of any labels except or most of the tube layout. The rest lost to time...  How do you like your set?? I think mine is my favorite tabletop set. I do have a couple of 5 band 16B's in the works both needing major cabinet work. I'm curious how they compare to the 116B.


Attached Files Image(s)
   

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Hi,
I am very impressed with this set.  My go-to set for shortwave entertainment has been my Scott All wave 23. The Philco 116 keeps pace with the Scott in bringing in distant stations.  I really like the two speed tuning knob on the Philco (even though it feels a bit rough - I got to revisit the tuning mechanism again).  The Scott only has single speed tuning.  All this pleasure and it still needs an alignment!  Can't wait till that is done.
So I must agree that the Philco 116B is my favorite table top and definitely one of my all-around favorite radios.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1397 online users. [Complete List]
» 1 Member(s) | 1396 Guest(s)
Avatar

>