Thorens TD124 restoration
Posts: 15,797
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
A few years ago, like maybe 6 or so, I bought me a Thorens TD124.I knew it would need some TLC before it .
So, now that I have some time on my hands, I decided to tackle it.
I am not a turntable man, like Kirk.
This said, I knew the turntable made attempts to turn when I bought it.
Today I took the platter off.
Immediate ovservation: the motor runs fine. Big whew! Even if it needs some lube (perhaps), it is running.
Here is the idler in 78 rpm down to 33 rpm positions.
1) the idler has cracks
2) in the 16 rpm it does not touch the shaft, and then it will touch it when pushed.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 04-28-2020, 08:22 PM by morzh.)
Posts: 15,797
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
The underbelly.
Also need to know a good place to get idlers.
One of the two setscrews on the hub that holds idler down refuses to come out.
Have tried PBlaster and heat.
No luck.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Should be a good player, here is where to check for idlers
https://www.thevoiceofmusic.com/
Posts: 15,797
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
$256.88 (at current exchange rate) for an idler wheel? Holy Cow! 
--
Ron Ramirez
Ferdinand IN
Posts: 15,797
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Yeah....considering what a fully working Thorens TD124 goes for.....
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Mike you might check Email V M and see if they can rebuild your idler.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
> Yeah....considering what a fully working Thorens TD124 goes for.....
Too rich for me. Guess I'll have to stick with a Technics.
--
Ron Ramirez
Ferdinand IN
Posts: 15,797
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Mike
Who are Email V M?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
The voice of music link above. Just thinking it might be worth emailing them to see if they could rebuild your idler wheel.
They usually respond fairly quick to email questions. I was hoping to save you some money and thought it's worth a try.
Posts: 15,797
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Mike
Thanks, I will write to them. Provided I can take that thing off 
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 04-28-2020, 11:36 PM by morzh.)
Posts: 3,135
Threads: 54
Joined: Apr 2011
City: Lexington, KY
Nice turntable Mike 
But like Ron, I'll have to stick with my Dual 1229 and maybe the Technics my late brother had and no one else wanted. Although I've kept all my vinyl I seldom listen to them.... my old ears are perfectly fine with the (debatably) inferior CDs.
The last time I played a record was to make a CD of a Neil Young album (American Stars 'n Bars) that (at the time) had never been issued on a CD. I drug my big receiver and turntable over to the PC and painstakingly recorded each track, and it turned out rather well. Then I noticed a few months later the record company finally released it on CD.
None of this senseless rambling helps you get your Thorens working again, but that $250+ idler looks pretty nice, but you would think there would be more demand for them making the cost a little more reasonable. Maybe you'll get more feedback at Audiokarma..... nevermind, I see you already posted over there.... good luck!
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 15,797
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
John
Yep, I am getting some good advice there on the AK.
Some advise rebuilding, some the aluminum one with the o-ring.
First oder of the day is to try to take it off. One set screw just doesn't budge.
I am dripping PB on it, every few hrs . In a couple of days I will try again as so far I am just damaging the screw.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 15,797
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Just called the Voice of Music.
They either send you the part from stock (rarely), which is someone's old re-rubbered part, IF you send them your old part, or you just send the old part and wait for it to be re-rubbered. Takes 4-5 weeks.
Quite ok, no rush. It has waited 6 years, will wait a few months more.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 05-06-2020, 05:23 PM by morzh.)
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
I take it you got the idler wheel 0ff?
Users browsing this thread: 6 Guest(s)
|
|
Recent Posts
|
|
IF can wire size and Rubber mounts?
|
| Hello PHORUM members,
I am still working on restoration of my PHILCO 37-640. I want to start with rewiring the IF ca...georgetownjohn — 06:32 PM |
|
Gilfillan Brothers Car Radio?
|
| There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM |
|
Looking for verification of correct schematic.
|
| Definitely 870044RossH — 01:12 PM |
|
12' Philco
|
| Wonder if the chassis was big too.daveone23 — 12:38 PM |
|
Philco 38-2 Automatic Tuning
|
| Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM |
|
Hickok AC51 tube tester
|
| How does the 5W4 and 83 tube filaments get fed?martinj — 12:25 PM |
|
462ron
|
| Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM |
|
Philco 38-2 Automatic Tuning
|
| I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM |
|
Philco 38-2 Low Volume
|
| I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM |
|
Philco Speaker Spider
|
| Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM |
|
Who's Online
|
There are currently 4045 online users. [Complete List]
» 1 Member(s) | 4044 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
