1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Gallery and decal placement
Radioroslyn
Phorum Expert
*****
Posts: 7,287
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#1

05-25-2020, 09:11 AM
I was looking at some pics in the gallery and saw this one.  https://philcoradio.com/gallery2/1934a/#..._504L_505L
A couple of things peaked my curiosity. The PHILCO logo above the speaker? Maybe but have seen many sets with it above the knobs or close to the dial escutcheon. Just looks a little out of place. The decal at the top looks to be the same one I have on my 2nd 16B, Sherman Clay and Sons.       Maybe a set that was sold in the west coast. From what I've read the SC dealers started out west and moved eastward. The 16B came from Fla when I got it but it's had 86yrs or so to find way over to this side of the states.
Now I need to figure out a way to keep the decal while doing the refinishing. Have a few idea but have to pickup a few things before I can try.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
Nathan Slingerland
Super Moderator
******
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#2

05-26-2020, 11:23 AM
Looks may be like this repro decal?

https://www.piercepianoatlas.com/catalog...ts_id=3614
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,287
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#3

05-26-2020, 12:21 PM
This one is a bit smaller at 1 3/4 x 1/2. Didn't realize that it was that popular of a company to have it own repro decal.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration