Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 39-7 restore help
#16

I haven't had much problem with the wires coming loose. They are usually wrapped around the terminal several times. I would try to solder the wire to the part that is protruding that is within your drawn circle. Any connections to the top of the terminal can then be soldered quickly so the heat does not have time to transfer all the way down to the coil wire. Secure the wire on the surface with some sort of adhesive.
#17

I would tin then solder a short piece of 24 gauge wire to the terminal then connect the winding to the short piece. In effect, extending the terminal.

Rod
#18

Looks like you have enough wire left the resolder it to the terminal. Would clean off the old solder w/a solder sucker or wick. Wrap the wire around the terminal a turn or two. Then resolder. The wire has cotton or silk covering which most of the time can be carefully removed with a fingernail. The wire under the covering has a lacquer coating which the solder will burn off.
If you don't think you have enough to wrap around then use a strand from some stranded wire. Wrap it around the terminal and solder. Solder the other end the broken wire on the coil.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#19

Thanks for the good suggestions. I will try a repair first.

John




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM
American Bosch Model 802 auto radio
I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM

[-]
Who's Online
There are currently 7324 online users. [Complete List]
» 2 Member(s) | 7322 Guest(s)
AvatarAvatar

>