1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Finally out of the attic!!!
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#1

08-16-2020, 11:14 AM
    Well guys, I finally pulled this beauty out of the attic with a little help. Managed to not damage it getting it down. Everything seems to work!! The tube take a couple minutes to warm up and the speakers have explosions of sound quite a bit while tuning and adjusting the volume but the sound does come through at low levels. If anyone has any advice on components that should be preemptively replaces to ensure the set keeps operating or any tips in general, I would sure appreciate it.                
(This post was last modified: 08-16-2020, 01:31 PM by 43ddoc. Edit Reason: Add picture )
Find
GarySP
Super Moderator
******
Posts: 2,191
Threads: 159
Joined: Jan 2013
City: Westland, MI
#2

08-16-2020, 11:21 AM
First tip ... DO NOT plug it in again until you replace capacitors and any out of spec resistors. Plugging in a set full of old components is just asking for disaster to happen. By the way, what model are you commenting about ... no photos are attached. Take care and BE HEALTHY! Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#3

08-16-2020, 11:25 AM
    Well guys, I finally pulled this beauty out of the attic with a little help. Managed to not damage it getting it down. Everything seems to work!! The tube take a couple minutes to warm up and the speakers have explosions of sound quite a bit while tuning and adjusting the volume but the sound does come through at low levels. If anyone has any advice on components that should be preemptively replaces to ensure the set keeps operating or any tips in general, I would sure appreciate it.            
(This post was last modified: 08-16-2020, 01:34 PM by 43ddoc.)
Find
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#4

08-16-2020, 11:29 AM
I’m trying to attach photos but they don’t seem to load.
Find
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#5

08-16-2020, 11:35 AM
Original post
https://philcoradio.com/phorum/showthrea...#pid146422
Find
klondike98
Phorum Moderator
******
Posts: 5,204
Threads: 276
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#6

08-18-2020, 01:03 PM
I merged your two "Finally out of the attic" posts together.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
Radioroslyn
Phorum Expert
*****
Posts: 7,305
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
#7

08-18-2020, 03:27 PM
As Gary said replace the capacitors. It's probably new enough that it most are going to be ceramic. On the other hand the eletrolytic caps should be replaced if they haven't been in the last 20yrs or so. The picture of the screen tells me that there maybe an issue with the power supply as the raster isn't filling the screen. Definitely would measure the hv at the p/s and the boost line to see if it is within reason.

GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
PhilcoJohn
Phorum Expert
*****
Posts: 1,470
Threads: 97
Joined: Jul 2012
City: Poughkeepsie, N.Y.
#8

10-08-2020, 06:36 PM
Wow nice unit! As Gary said do not plug it in again before you or someone else goes  through the whole console. You do not want to burn it up.  Icon_e_sad
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
1949 Motorola 5A9M
bob  Nice work on battery . If you don't. Have terminals i have a few spares  Samsam — 02:12 AM
1949 Motorola 5A9M
hello mr Fixr, for sure !! I have some radios that I need to make some batteries for too. Sincerely richardradiorich — 12:33 AM
1949 Motorola 5A9M
Dittos, sweet b on the battery. Love the "9 Lives" logo, remembered from my childhood. Other neat ones are t...MrFixr55 — 11:24 PM
Philco 46-1209 strange behavior
Hi Morzh, Dunno if the AC EMI caps are an issue. I never liked the concept but never had an issue with these causin...MrFixr55 — 11:21 PM
Philco 46-1209 strange behavior
And no hum without the 7AF7? Not common but I am thinking heater - cathode short. This would introduce hum in this sta...MrFixr55 — 11:14 PM
schematics
Those filter caps in the cardboard tube are easy to restuff, especially the kind with the rolled over end. You don't hav...Arran — 09:56 PM
Philco Model 16 wiring question
If you have 5 wires, do this: The wires that go to thick-wire wound winding are the filament. If you do not know wha...morzh — 09:03 PM
Philco Model 16 wiring question
I recently acquired a Philco Model 16 Code 126. I removed the power transformer to place heat shrink on some very bad...bobclausen — 08:23 PM
1949 Motorola 5A9M
Hello Bob, That battery looks great nice job ! Sincerely Richardradiorich — 08:20 PM
1949 Motorola 5A9M
Yes, I plan to put a Velcro closer on the top.klondike98 — 07:28 PM

[-]
Who's Online
There are currently 1092 online users. [Complete List]
» 3 Member(s) | 1089 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration