1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Finally out of the attic!!!
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#1

08-16-2020, 11:14 AM
    Well guys, I finally pulled this beauty out of the attic with a little help. Managed to not damage it getting it down. Everything seems to work!! The tube take a couple minutes to warm up and the speakers have explosions of sound quite a bit while tuning and adjusting the volume but the sound does come through at low levels. If anyone has any advice on components that should be preemptively replaces to ensure the set keeps operating or any tips in general, I would sure appreciate it.                
(This post was last modified: 08-16-2020, 01:31 PM by 43ddoc. Edit Reason: Add picture )
Find
GarySP
Super Moderator
******
Posts: 2,137
Threads: 158
Joined: Jan 2013
City: Westland, MI
#2

08-16-2020, 11:21 AM
First tip ... DO NOT plug it in again until you replace capacitors and any out of spec resistors. Plugging in a set full of old components is just asking for disaster to happen. By the way, what model are you commenting about ... no photos are attached. Take care and BE HEALTHY! Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#3

08-16-2020, 11:25 AM
    Well guys, I finally pulled this beauty out of the attic with a little help. Managed to not damage it getting it down. Everything seems to work!! The tube take a couple minutes to warm up and the speakers have explosions of sound quite a bit while tuning and adjusting the volume but the sound does come through at low levels. If anyone has any advice on components that should be preemptively replaces to ensure the set keeps operating or any tips in general, I would sure appreciate it.            
(This post was last modified: 08-16-2020, 01:34 PM by 43ddoc.)
Find
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#4

08-16-2020, 11:29 AM
I’m trying to attach photos but they don’t seem to load.
Find
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#5

08-16-2020, 11:35 AM
Original post
https://philcoradio.com/phorum/showthrea...#pid146422
Find
klondike98
Phorum Moderator
******
Posts: 5,163
Threads: 273
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#6

08-18-2020, 01:03 PM
I merged your two "Finally out of the attic" posts together.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
Radioroslyn
Phorum Expert
*****
Posts: 7,297
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#7

08-18-2020, 03:27 PM
As Gary said replace the capacitors. It's probably new enough that it most are going to be ceramic. On the other hand the eletrolytic caps should be replaced if they haven't been in the last 20yrs or so. The picture of the screen tells me that there maybe an issue with the power supply as the raster isn't filling the screen. Definitely would measure the hv at the p/s and the boost line to see if it is within reason.

GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
PhilcoJohn
Phorum Expert
*****
Posts: 1,469
Threads: 97
Joined: Jul 2012
City: Poughkeepsie, N.Y.
#8

10-08-2020, 06:36 PM
Wow nice unit! As Gary said do not plug it in again before you or someone else goes  through the whole console. You do not want to burn it up.  Icon_e_sad
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Zenith H725
1.7-3.9 %, a modified Sine wave inverter is around 25%. Most generators from big box stores run 10% at a 50% load. What ...David — 04:06 PM
My Philco 37-116 Restore
I am having a heck of a time doing the alignment on the AM band. I can't seem to dial in the 1500 KC oscillator. I can h...dconant — 03:35 PM
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM

[-]
Who's Online
There are currently 529 online users. [Complete List]
» 3 Member(s) | 526 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration