Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith 8S-531
#1

Looking for a detailed layout of the underside of this radio.. Parts layout and wiring..

USES CHASSIS Number 8A02

Does anyone have or maybe worked on this and has some detailed drawings they made??

Thanks

Skip
#2

Anyone have a clue to what this is? and were the white wire goes??


[Image: https://live.staticflickr.com/65535/5026...b57f_c.jpg]

Skip
#3

Wherever the white wire is supposed to go it's a fairly late addition to the radio, probably because the original was a crumbling rubber wire.

Maybe that's the antenna coil?  It's hard to tell from that small view, can you post a picture of the entire underside of the chassis?

For anyone following the schematic is in volume 12, Zenith p. 12-18

.pdf Zenith 8-S-531.pdf Size: 936.66 KB  Downloads: 195

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#4

First you need to figure out which coil it is (ant or osc). Then use an ohm meter to see what relationship the white wire has to the other terminals on the coil. Using the schematic sort out where the wire goes. Piece of cake!! Icon_twisted

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2622 online users. [Complete List]
» 2 Member(s) | 2620 Guest(s)
AvatarAvatar

>