Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco similar to 41-90CB
#1

Dear Friends
I have a Philco Tropic radio similar to the model 41-90CB, but mine has SW bands. This radio was working fine, but all of a sudden, it started to not tune in any AM radio stations
However, the aux input is working ok
What do you think it might be wrong?
I suspect a problem with inner antenna wiring
Thanks for your help
P.S. If anybody can identify the radio model, I'll appreciate it
Regards


Attached Files Image(s)
   
#2

Not tune in any AM station = no stations at all, rihgt?

Well, it could be anything. I doubt it is wiring: wires do not break off or desolder by themselves. It might be a coil or a tube from the RF section. Oscilaltor not working also = a bad coil.
So....if you could troubleshoot, break out your ohmmeter and buzz the coild through, and test the tubes from the RF and oscillator section.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Welcome. Looks like it might be one of these models'
https://philcoradio.com/gallery2/1942a/#...7T_42-718T
#4

Thanks for the info
#5

If you post a pic of the back innards was can sort out which set it is.
The determining factor is the power supply. DC, AC/DC, or AC.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Thanks, I have the model number now




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5600 online users. [Complete List]
» 1 Member(s) | 5599 Guest(s)
Avatar

>