Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA 10T
#61

The unmolested chassis. Don't think any technician had their grubby paws underneath.
TEST:


Attached Files Image(s)
   
#62

S'more stuffs for viewage:


Attached Files Image(s)
           
#63

I have about 750 photos I took of its' progress in the past 7 weeks. Lol:


Attached Files Image(s)
                   
#64

And another blast:


Attached Files Image(s)
                   
#65

That sure cleaned/polished up pretty nice Icon_thumbup

I guess all that dust was a good protective layer for extended storage Icon_e_wink

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#66

And some chassis stamps: (there are many more that were taken in the clean up,  but my eyes are going crisscross now. You get the drift)... XD


Attached Files Image(s)
       
#67

Thanks John!!!!! This is by far the nicest chassis I've ever laid my hands on, or even seen in person!!!!!  Icon_clap
Yes, I believe the thick layer of dust, and I assume a heavy coating of cigar/cigarette smoke contributed to the preservation of this gem of a chassis!!!!! 
Funny tho. The dust layer was SUPER thick under the magical brain cover. Far heavier than what was on the power chassis!!!  Icon_eek
P.S. this was only a 60+ hour clean up, and it still really isn't quite finished yet, but it's as far as I'm going on it...
Oh, and, all switches, transformers, and everything else I checked was either spot on, or in tolerance. Icon_smile




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 6787 online users. [Complete List]
» 1 Member(s) | 6786 Guest(s)
Avatar

>