Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Grundig Majestic 4095
#16

OK Finally got the knobs off what a pain..  Removed glass.  Now I can get to the dial strings  All are broken and all over the place..  DOES anyone have a Dial string Diagram???  The one I have makes NO since..

Morzh, I could not find that cap on the underside of my radio.  Will have to take some pictures..

At lease making progress..

No since of doing recap until I can figure out the dial strings..

Skip
#17

Skip

It's OK. I am sure I did it right, I take photoes, just second-guessing myself.

Glad you got those knobs off, what a pain.

When I took my electrolytic and the transformer off, I found out that soooooooper-looooong mounting strip is broken. But it is held well by those parts soldered to it. I will use epoxy when done with recapping.

Now mulling the prospects of restuffing the electrolytic cap.
By the way, have you seen that extra-soooooooooooper-loooooong electrolytic cap under the audio transformer? It is like 4" long and 1/6" in diameter or something. Never saw anything like it.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#18

I have decided to stop doing anything on the one I have.. Due to the Rust on the push button assembly.. I cannot even get the power on to stay in the on position..

No way I could take the assembly out to many wires to disconnect..

Skip
#19

Skip

Sorry to hear that.
Was it kept in a wet place?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#20

Good question no clue.. I got it from a antique place up by me. He has been having me go over all radios and tube amps that come into his store.. To make sure they are working.. So I fix them if they do not work.. But he doesn't want to spend a lot of money getting these working as he has to resell them..

Skip
#21

Skip,

You wouldn't have the owners manual for this thing, would you? I have the SAMS now, it's a great help, but the owners would be very handy thing to have.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#22

No I don't.. All I have is a schematic in German,, Could not even find a Sams on it..

I talked to the Antique guy and he said he still would like to get it working.. Well I tried to measure the TRansformer Primary Open.. But then found a fuse that was broken in half Its a small dia about .2 inches and probably 1.5 inches long.. Good luck in finding that.

Skip
#23

Fuse...regular 1-1/2 inch one. I bough it on Amazon, a whole box. 0.7A - I use 1A.
The selenium will probably be good. Mine is good, all voltages are where they should be.
You might get away without replacing main electrolytic - I did replace mine but it measured well. Maybe some reforming, considering the age.
Otherwise removing that transformer under which it is, is a royal pain.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>