Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Did Philco Make a Good AM-FM Table Radio?
#1

I thought I would ask this seeing as I now have a couple good Zeniths and finally have a good RCA AM-FM table radio in my stable. Did Philco make a good AM-FM table radio and what model would it be? So far I have only seen small units in poor shape around here, so the jury is out on that for me. It seems odd to have two of what I consider the original 'Big Three' of radio sales represented without a Philco example.

No matter where you go, there you are.
#2

Well I guess it depends on what year you're interested in. The first table model with FM is one of the best, the 48-482. A huge beast, basically a console in a table model. Has AM/FM and short wave.

Greg V.
West Bend, WI
Member WARCI.org
#3

Year doesn't really matter here, just in the tube era I would say. I have seen a few 48-482's in my area over the years, but they are usually trashed like most other late 40's Philcos are that I find around here. Also, it seems people's pets and kids loved to rip out both the grill cloth and the speaker cones in units I see.

No matter where you go, there you are.
#4

The 48-482 I restored had a great sound. Gave it away as a gift.
#5

       
I would vote for Philco model 53-956  my only Philco AM FM. Found at the local flea market summer of 2011.
#6

I have often been leery of FM Philco due to their reluctance to pay for the "Armsrong System".

Paul

Tubetalk1
#7

Thanks for the advice thus far. I almost bought a model 53-956 a few years back, but was a bit hesitant at the time and missed out. I was looking at a nice condition 49-906 with a bad cord today, but am trying to research that one first. I have a big Philco AM-FM and it's matching console from 1948 that both use two 117Z3 rectifier tubes. The console is fair, but tries to play and the table unit has a livable cabinet, but the best way to describe the inside is 'bio-hazard'. Some critters made a mess in there! In spite of that, it tried to power up and I got a little audio out of it. Not sure what to do with those two.

Edit: They are 1949 models. The table 'bio hazard' one is a 49-909 and the console is either a 49-1100 or 49-1101. Had them for a while.

No matter where you go, there you are.
#8

Maybe clean out the old nest, and then give it a check up. Paul

Tubetalk1
#9

There's no nest, just plenty of droppings... Chassis isn't too bad, but the screws that hold the chassis in on one side are totally rusted. If I could get it out I MIGHT have a chance to clean out the cabinet and chassis. I don't think it was mice that left the crap in this radio, it almost looks like from birds or other critters.

No matter where you go, there you are.
#10

Wear a mask and gloves, wipe it out with alchohol on a rag or such. Be careful.

Paul

Tubetalk1




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4890 online users. [Complete List]
» 1 Member(s) | 4889 Guest(s)
Avatar

>