Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

47H Philco DC radio worth restoring?
#1

Hi, I found Philco Radio 47H for sale pretty cheap in my area. Cabinet looks in good shape it has 2 speakers and as far as I can tell from the pictures this is a 47H model which is 120 VDC only. I have a couple of questions before buying it, is it worth restoring since I'd have to build a 120v ac to dc converter to operate it, and how difficult is it to build one? Second, the owner said he plugged it in, probably didn't realize it was DC only, and stated it was loud static coming out of the speakers. Could he have damaged the radio by plugging into AC directly? Thank you,
#2

Yes the radio possibly could suffer from being plugged to AC, but not necessarily.

Building the AC/DC could be as simple as building a rectifier bridge and a capacitor. If you use a Pi-filter, 2 caps and a resistor, the resistor could take care of dropping out the excess voltage.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

I did some back of the envelope calcs and on 50W load to drop to 115vdc from about 170vdc rectified I'd need 25W resistor. It seems I'd need to use a transformer but i think 120vac to 80vac are pretty rare/expensive, at least i have not found one yet.
#4

What about using a half wave rect instead of full bridge look into using a bucking transformer (24 volts?) to reduce the ac input to the half wave. Good luck David
#5

If you were to use a capacitor to drop the voltage first then you could rectify the rest without losses or much losses.
Also tube rectifiers drop some voltage due to the higher plate impedance.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

Old school a 120 volt DC generator. Did not know one could find a new motor/generator a modern day light plant.  https://www.ebay.com/itm/1-hp-120-volt-e...Sw9~RXJUy3   Old stuff on you tube  https://www.youtube.com/watch?v=x6eKGqpxiwE




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM

[-]
Who's Online
There are currently 2904 online users. [Complete List]
» 1 Member(s) | 2903 Guest(s)
Avatar

>