Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 71tone control internal cap value
#1

Hello all, I hope you are weathering the pandemic storm and are doing well. I am starting my first fall project a model 71 cathedral. The tone control, item# 39 in Beitman's parts list lists part number 04757 but gives no value. The part number on my tone control is 05153. The radio looks untouched and this appears original, but no idea. My wires are of course crusty and will need to be gutted and replaced. Any help is appreciated, thanks.
#2

There are 2ea. .01 uf. inside.
#3

Look here under 1932, the schematic for the 71 is there with the value of parts.

https://philcoradio.com/library/index.ph...chematics/
#4

https://philcoradio.com/library/index.ph...chematics/    Always best to look here first, Ron has got to a lot of work to mark the values on these schematics.

Steve

M R Radios   C M Tubes
#5

Ok thanks Dale. I cannot find a clear schematic the item designators are blurry and I only see one cap in the schematic near the output tube; do you have a better diagram? Sincerely, Jeff
#6

Got it, thanks all, have a great day!!
#7

Jeff,

This will help.


Attached Files Image(s)
   
#8

Dale that sure does help, thank you very much!!




Users browsing this thread:
[-]
Recent Posts
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. S...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM

[-]
Who's Online
There are currently 1420 online users. [Complete List]
» 3 Member(s) | 1417 Guest(s)
AvatarAvatarAvatar

>