Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Replacement for .7 to 1 interstage transformer
#1

Had a similar thread, but it wasn’t as specific as this, and therefore got lost. Anyone know a good replacement for this interstage transformer? Has a turns ratio of .7 to 1. It’s in a Sparton 28.

[Image: https://i.imgur.com/lNO85AP.jpg]
#2

It can not be .7 to 1.
Just by the sheer DC resistance, even if accounted for the wire gauge, 700 Ohm to 1 Ohm means huge difference in the number of turns.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Morzh,

Look at the schematic. Primary at 3580Ω, secondary center-tapped at 2985Ω (or 5970Ω total secondary). equals a turns ratio of actually .599 to one, but close enough to the rated value of .7 to 1. Am I missing something here?
#4

Morzh,

Oh, I see. Your're looking at the output transformer. I'm referring to the input or interstage transformer.
#5

Oh..yes I was looking at the output.

38-116 has a similar one.
Lets' see if Tubes and More has something.
Nope. They have 1:2 and 1:3. Can't see that ratio around.
Maybe someone else can.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

I found a 1:1.5 but that was the lowest. Did find a 1:1 but was discontinued.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#7

1:1.5 and 0.7 to 1 are close enough.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#8

It's a Hammond 124D

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#9

Great! Thanks Terry. I'll get a 124D and give it a shot.

Pat




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-480 Cabinet Restoration
Nice work! Take care and BE HEALTHY! GaryGarySP — 11:29 AM
Philco 46-480 Cabinet Restoration
Thank you!jrblasde — 10:00 PM
Philco Model 95 High Boy
So today I get published as I update my collection in the Radio Museum web site. I tried to published pictures of my Phi...slford310 — 08:00 PM
Philco 84 antenna connection
Very simply connect al long piece of wire to that contact for your antenna.   A piece 10 to plus 50 feet is no issue dep...slford310 — 07:46 PM
Philco 46-480 Cabinet Restoration
I like it!Burchjburch — 05:57 PM
Philco 46-480 Cabinet Restoration
I knew when I asked the question here, that I just wasn’t satisfied with the darkness of the stain. Today I took some mi...jrblasde — 04:54 PM
Philco 84 antenna connection
I've used a single long wire up as high as possible and away obstacles. The gnd can be connected to a copper water pipe ...Radioroslyn — 03:34 PM
Philco 51-632
Found this today for $10 in the local resale shop. It’s a violation of good procedure but I put it on the variac. It cam...bridkarl — 03:25 PM
Philco 41-221 Restored
Rod Great job, looks good, no need to refinish to my taste. It is rare that you see the tenite grill in these in decent...morzh — 03:01 PM
My last cabinet for this year
Beautiful Job!!!! Looks awsomeslford310 — 03:01 PM

[-]
Who's Online
There are currently no members online.

>