Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Replacement for .7 to 1 interstage transformer
#1

Had a similar thread, but it wasn’t as specific as this, and therefore got lost. Anyone know a good replacement for this interstage transformer? Has a turns ratio of .7 to 1. It’s in a Sparton 28.

[Image: https://i.imgur.com/lNO85AP.jpg]
#2

It can not be .7 to 1.
Just by the sheer DC resistance, even if accounted for the wire gauge, 700 Ohm to 1 Ohm means huge difference in the number of turns.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Morzh,

Look at the schematic. Primary at 3580Ω, secondary center-tapped at 2985Ω (or 5970Ω total secondary). equals a turns ratio of actually .599 to one, but close enough to the rated value of .7 to 1. Am I missing something here?
#4

Morzh,

Oh, I see. Your're looking at the output transformer. I'm referring to the input or interstage transformer.
#5

Oh..yes I was looking at the output.

38-116 has a similar one.
Lets' see if Tubes and More has something.
Nope. They have 1:2 and 1:3. Can't see that ratio around.
Maybe someone else can.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

I found a 1:1.5 but that was the lowest. Did find a 1:1 but was discontinued.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#7

1:1.5 and 0.7 to 1 are close enough.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#8

It's a Hammond 124D

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#9

Great! Thanks Terry. I'll get a 124D and give it a shot.

Pat




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>