1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 70
Radioroslyn
Phorum Expert
*****
Posts: 7,297
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#1

01-25-2021, 12:49 PM
Will a tube shield from a 70 fit a model 71? Have had a few 70's but don't think I've fooled with any 71's.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
rfeenstra
Phorum Expert
*****
Posts: 1,199
Threads: 49
Joined: Oct 2017
City: Allendale, MI
#2

01-25-2021, 03:59 PM
It will, I just tried it, but the grid wire from the coil that is under the shield .will need to be extended to get around the the extra "partition" that is in the 70's shield.
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,297
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#3

01-25-2021, 05:24 PM
Tnx!!
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
1.7-3.9 %, a modified Sine wave inverter is around 25%. Most generators from big box stores run 10% at a 50% load. What ...David — 04:06 PM
My Philco 37-116 Restore
I am having a heck of a time doing the alignment on the AM band. I can't seem to dial in the 1500 KC oscillator. I can h...dconant — 03:35 PM
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM

[-]
Who's Online
There are currently 459 online users. [Complete List]
» 1 Member(s) | 458 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration