1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
RE: Restoration - 46-350
Donald
Junior Member
**
Posts: 4
Threads: 2
Joined: Dec 2020
City: Garden City State, Province, Country: MI
#1

03-21-2021, 08:40 PM
I am restoring a 46-350 and have replaced the caps and the electrolitic can caps also the ac cord . The problem I have is that with the on/off switch in the off position when you plug in the set the tubes light up and then when you turn on the radio the volume is already at a comfortable level . So when I shut off the radio I have to unplug it any help will be appreciated
Find
morzh
Odobenus rosmarus
******
Posts: 16,482
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#2

03-21-2021, 09:37 PM
The sch shows everything is disconnected when the switch is off.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Bill Bacco
Member
***
Posts: 94
Threads: 9
Joined: Feb 2013
City: Monroeville, PA
#3

03-21-2021, 10:43 PM
Have you tested the switch with an ohm meter? (Be sure to unplug from AC) If so and it is not showing as opening and closing, you may need to take it apart and clean it. If that doesn't work, it may need replaced. It is also possible that someone jumpered it out.
(This post was last modified: 03-21-2021, 10:45 PM by Bill Bacco.)
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1026 online users. [Complete List]
» 1 Member(s) | 1025 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration