Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Dial Scale Removal
#1

I've a model 610, just 610 that's going to need the dial scale replaced. I know there are repros out and that's great, but how do you remove those scales off of their mountings? Can someone direct me to an illustration or just let me know how it's done on this forum?

This set was mentioned earlier on in the forum. Wow, what a player. Just jumpered in a few 10mfd's to get rid of the LOUD HUM to hear if it's going to be a player or not. Sounds real good. Back to the soldering tool to do it right. Thanks all for your help.

GB

73 de,

Gary/N9VU
#2

That 1 1/2 inch perforated disc in the center of the dial- put the tips of your needle nosed pliers in the holes and turn counter-clockwise just a bit. The disc will fall off; the dial simply pulls off the two pins.

In getting a replacement I recommend Mark Oppat at Antique Audio (moppat@comcast.net ); his dials are nearest to the original in color although somewhat darker. The RockSea dials are VERY light in color and look odd in my opinion.

Pete AI2V
#3

AI2V Wrote:That 1 1/2 inch perforated disc in the center of the dial- put the tips of your needle nosed pliers in the holes and turn counter-clockwise just a bit. The disc will fall off; the dial simply pulls off the two pins.

In getting a replacement I recommend Mark Oppat at Antique Audio (moppat@comcast.net ); his dials are nearest to the original in color although somewhat darker. The RockSea dials are VERY light in color and look odd in my opinion.

Hey, thanks for the info. I didn't realize it was that simple. I'll give it a
try. Thanks for the advice on dial covers as well. I've only bought one in my radio career from RocksSea and you're correct, looks a bit brighter than usual, but I do like it. Thanks again for the helpful advice. GB.

73 de,

Gary/N9VU




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 96 cabinet veneer
There is some description of the veneers in the 1930 Brochure in our library. Here's the link: klondike98 — 11:59 PM
Philco 91 Speaker Replacement
I can't remember, but there was a particular product for loosening glue on the more modern "spiders", used pos...MrFixr55 — 09:43 PM
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM

[-]
Who's Online
There are currently 1588 online users. [Complete List]
» 2 Member(s) | 1586 Guest(s)
AvatarAvatar

>