Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

42-350 Help
#1

HI, I'm new to the forum.

This is a tough project, lots of rotten wires and this radio probably was worked on before unsuccessfully.  I have a couple of questions if someone can help.

1. On the 42-350 schematic the FM IF transformer part #44 shows 4 coils on the secondary side.  I might have uploaded an clip of that part.  Between the bottom two coils it is labeled BLUE.  Is the top of the bottom coil connected to the bottom of the coil next to it ?  The schematic is unclear.  I have the transformer apart and am replacing wires.  There is no BLUE wire, but maybe it has faded to dirty white.  

2. On the left side of the chassis view from rear, there is a AM screw type antenna connection, then going to the right, a FM plug type antenna connection, then over to the right side on the rear there is a single pin connector.  That wire was loose in the chassis, what is it?  So far I can't find it on the schematic.

3. In the Philco world, what does CODE 121 mean ?

I bought this radio at a hamfest 10 years ago, when I looked inside after I got it home, I put it on the shelf.

rich

   
#2

Is the top of the bottom coil connected to the bottom of the coil next to it ?

No.

...there is a single pin connector. That wire was loose in the chassis, what is it?

Can't help you here as I do not own a 42-350.

...what does CODE 121 mean ?

The "code" numbers signify production changes. The original design was Code 121; later changes would usually (but not always) result in a new code such as 122, 123, etc.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 5562 online users. [Complete List]
» 2 Member(s) | 5560 Guest(s)
AvatarAvatar

>