Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Magnavox 1FM031
#1

https://www.flickr.com/photos/92577012@N...9692099792

Why? Is a question that I ask myself sometimes, so who needs a 27 inch long radio? Guess I need a longer table. With the 2 large speakers it sounds very nice, even on AM. The FM could be a bit more sensitive but well in 1967 that may not have been a big worry. Case is nice, and it looks like a radio from the Dentist office that would play EZ Listening favorites. Hate to see it trashed because it is not Vacuum Tube.  Icon_eek

As I offloaded my last AM/FM Magnavox to a guy who is a FM Disc Jockey up here I now have a replacement. This is a better sounding set than that one, though the previous find had tubes. 

Paul

Tubetalk1
#2

It probably needs new electrolytic capacitors, especially in the FM section, and then possibly an alignment.

Impressive radio. I've seen pictures of those before but I did not know they were that large.

--
Ron Ramirez
Ferdinand IN
#3

I have cleaned the controls and it plays good though lytics need to go. I have not found too much documentation on this one. Fort Wayne Indiana.................

Paul

Tubetalk1
#4

Magnavox started out in Oakland, California and later moved to Fort Wayne, Indiana in 1931 by way of Chicago (1930). Fort Wayne was once the home of Slagle Radio, Steinite Radio, possibly others?

I just found a website dedicated to Magnavox history:
https://magnavoxhistory.com/

--
Ron Ramirez
Ferdinand IN
#5

My late friend Steve Hofer would roll over in his grave if I didn't mention that Farnsworth also had a factory in Ft. Wayne. Unfortunately the factory building has been torn down, but Philo's house remains.

Not to get too far off track, I like your new Magnavox Paul Icon_thumbup

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

Farnsworth - of course! Icon_redface Thanks John!

--
Ron Ramirez
Ferdinand IN
#7

Sweating it off up here today, off day today, back to grind tmrw. Listening to the Magnavox. My tube sets today a bit staticky, is that a word? Maybe too humid, when drizzly or moist I seem to get intereference from high tension lines out back. The solid state not so much. Sounds very fine for what it is. Very nice low end and bass but does not muddy higher end on music. So a good Magnavox product.

Has that heavy tuning feel like a german set, as a freind told me it's the flywheel effect on the tuner. Hope the heat breaks soon. Music and a cold one on a 98 degree day. Living high.

btw, nice website Ron, many pretty things.

How hot is it sez Ed McMahon, Johnny sez it's so hot ............

Paul.

Tubetalk1




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>