1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Dial too low?
Croydonradio
Junior Member
**
Posts: 9
Threads: 4
Joined: Jul 2021
City: Ottawa State, Province, Country: Ontario
#1

11-23-2021, 07:57 AM
Wondering if others have ran into this and how to close that gap at the top. I don't think I can raise the chassis due to shafts coming through the cabinet. Would it likely be those rubber grommets that have shrunk over time, isolating the tuning capacitor? Its the Philco 37-361 Cdn.


Attached Files Image(s)
   
Find
radiorich
Phorum Expert
*****
Posts: 1,600
Threads: 101
Joined: May 2008
City: Omak State, Province, Country: WA
#2

11-23-2021, 09:27 AM
Hello Croydonradio,
Well far as Brightness I am not sure how bright it should be but I don't think that one is to bright .
my Philco 38-10t has the same dial but I have not started restoration of it yet.

Sincerely Richard
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#3

11-23-2021, 09:34 AM
> Would it likely be those rubber grommets that have shrunk over time, isolating the tuning capacitor?

Yes, plus the grommets which originally were placed under the chassis; those are often missing now.
--
Ron Ramirez
Ferdinand IN
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

11-23-2021, 09:36 AM
>Would it likely be those rubber grommets that have shrunk over time, isolating the tuning capacitor?
Yup. If you can shake the tuning cap by wiggling the tuning shaft they are shot.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM
American Bosch Model 802 auto radio
I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration