Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Stupid Q Did the Brit or Canadian sets
#1

Use metric hardware? Have never had one.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#2

The Brits used Whitworth years ago. We bikers run into the problem with old English motorcycles like BSA and Triumph... It is different from SAE and is not metric either.
#3

Whitworth wrenches are marked the size of the bolt they fit not the size of of bolt head or nut. Plus the head size is in tenths of a inch. Thread pitch is 55 vs 60 for sae. I still have a set of whitworth tools just have not found anybody that I dislike enough to leave them to in my will! Stay safe David
#4

Metric came into legislated use in Canada in the early 1980's. Before that we used the same system as was used in the U.S.A.
#5

Up until around 1938, most of the chassis that went into Philco (UK) sets were made in Philadelphia and then sent over to Perivale.

I've owned as many as four British Philcos at one time (now down to two) and had no issues with hardware. Ditto the Canadian Philcos that have passed through here.

--
Ron Ramirez
Ferdinand IN
#6

The only difference in hardware between Canadian and U.S built Philco sets is that the Canadian sets may have used Robertson socket head screws in the cabinets, since the cabinets wee often made by outside firms, the chassis hardware is the same as the U.S ones mostly, meaning hex heads.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently no members online.

>