Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Tropic 103 valve radio made in England
#1

Had this Philco Tropic 103 come my way can find little about it i guess its a export model for the Commonwealth 
Valves EM81/ECH81/EBF89/EBC81/EZ80/EL84
 
WAVEBANDS 19M/25M/31M/SW1/SW2/BC


I believe its similar to the model UK 135

can find little around the web and no circuits for either of these 2 models


Attached Files Image(s)
                               
#2

I did find this but it's a bit hard to read.  https://www.todocoleccion.net/radios-ant...~x39757856 Seem that it's the same as the 101 model.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Radio Museum has this but doesn't seem to have a schematic:
https://www.radiomuseum.org/r/philco_tro....html#data
#4

I have a copy of the UK Vintage Radio service data DVD, and Model 103 is not in there (neither is model 101).

I used to have one of those sets. I would guess very few made their way over here to the USA. It was likely made for export to Africa and possibly South America.

--
Ron Ramirez
Ferdinand IN
#5

Thank Folks parts list will be useful sadly the circuit not so clear but much better than none at all
#6

Very attractive set !!

I find it interesting that although it is made in the U.K. the connections on the back say "antenna / ground" instead of "aerial / earth". I wonder when the U.K. producers started using those terms?
#7

.... and .... having read the radio specifications from the link above (for the 101), it only has two SW bands, but three "bandspread" dials .... not often we see "band spread" on consumer sets. GE made one in the fifties, (X371/CX371) a huge table top set with a half-round dial and two chassis'. This Philco looks to be a nice compact set by comparison.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM

[-]
Who's Online
There are currently no members online.

>