Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Tropic 103 valve radio made in England
#1

Had this Philco Tropic 103 come my way can find little about it i guess its a export model for the Commonwealth 
Valves EM81/ECH81/EBF89/EBC81/EZ80/EL84
 
WAVEBANDS 19M/25M/31M/SW1/SW2/BC


I believe its similar to the model UK 135

can find little around the web and no circuits for either of these 2 models


Attached Files Image(s)
                               
#2

I did find this but it's a bit hard to read.  https://www.todocoleccion.net/radios-ant...~x39757856 Seem that it's the same as the 101 model.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Radio Museum has this but doesn't seem to have a schematic:
https://www.radiomuseum.org/r/philco_tro....html#data
#4

I have a copy of the UK Vintage Radio service data DVD, and Model 103 is not in there (neither is model 101).

I used to have one of those sets. I would guess very few made their way over here to the USA. It was likely made for export to Africa and possibly South America.

--
Ron Ramirez
Ferdinand IN
#5

Thank Folks parts list will be useful sadly the circuit not so clear but much better than none at all
#6

Very attractive set !!

I find it interesting that although it is made in the U.K. the connections on the back say "antenna / ground" instead of "aerial / earth". I wonder when the U.K. producers started using those terms?
#7

.... and .... having read the radio specifications from the link above (for the 101), it only has two SW bands, but three "bandspread" dials .... not often we see "band spread" on consumer sets. GE made one in the fifties, (X371/CX371) a huge table top set with a half-round dial and two chassis'. This Philco looks to be a nice compact set by comparison.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
I got some new ceramic octal tube sockets installed and also tried some different coupling caps.  The results:  The go...TV MAN — 08:42 AM
Philco 46-1209 strange behavior
I pulled the tube out and it's shorted from pin 1 to pin 2. I suppose that's the problem...sq65 — 08:12 AM
1949 Motorola 5A9M
bob  Nice work on battery . If you don't. Have terminals i have a few spares  Samsam — 02:12 AM
1949 Motorola 5A9M
hello mr Fixr, for sure !! I have some radios that I need to make some batteries for too. Sincerely richardradiorich — 12:33 AM
1949 Motorola 5A9M
Dittos, sweet b on the battery. Love the "9 Lives" logo, remembered from my childhood. Other neat ones are t...MrFixr55 — 11:24 PM
Philco 46-1209 strange behavior
Hi Morzh, Dunno if the AC EMI caps are an issue. I never liked the concept but never had an issue with these causin...MrFixr55 — 11:21 PM
Philco 46-1209 strange behavior
And no hum without the 7AF7? Not common but I am thinking heater - cathode short. This would introduce hum in this sta...MrFixr55 — 11:14 PM
schematics
Those filter caps in the cardboard tube are easy to restuff, especially the kind with the rolled over end. You don't hav...Arran — 09:56 PM
Philco Model 16 wiring question
If you have 5 wires, do this: The wires that go to thick-wire wound winding are the filament. If you do not know wha...morzh — 09:03 PM
Philco Model 16 wiring question
I recently acquired a Philco Model 16 Code 126. I removed the power transformer to place heat shrink on some very bad...bobclausen — 08:23 PM

[-]
Who's Online
There are currently 1222 online users. [Complete List]
» 1 Member(s) | 1221 Guest(s)
Avatar

>