Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 70 serial number.
#1

So where is the serial number located? Is it stamped into the chassis on the rear? I ask because if it is then my 70 does not match the schematics. The number stamped on this chassis is 795,569 which should  have moved the volume control from the antenna coil to the input of the 1st AF detector. This one still has the control on the antenna coil.
#2

Two stamps, top and back side on several of mine.


Attached Files Image(s)
       
#3

It's a dual volume pot, the 5k side feeds the antenna coil - the 250 ohm side feeds two 24 tube's cathodes.
#4

Well I guess then the actual serial number for the later version must actually start with a letter. I looked right past the fact that this radio has the 4-24 tubes installed rather than the 1 in the later version. I picked this up in Kutztown last month as a working radio. Unfortunately the seller did not disclose that it was a semi-working radio. It picks up stations but the audio is badly distorted.
#5

Jim,

Yes, according to the survey chart that was published in the ARC magazine (a couple decades ago now  Icon_eek ) the serial numbers on the later 70 and 90 sets built after Dec 1931 started with A,B,and C respectively.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM

[-]
Who's Online
There are currently 2763 online users. [Complete List]
» 1 Member(s) | 2762 Guest(s)
Avatar

>