Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1934/35 16RX chairside
#1

Question is does the control panel have a PHILCO decal on it? One examples in the gallery doesn't really have a good depiction of reality. And the other is original but it doesn't look like it had one. Can't imagine it not having a logo on the set somewhere.

I just got it back from Kirk which he reveneered the top and grainfilled it. I've got to put a few coats of sanding sealer just  so I can see if needs some toning. I looks wonderful before the ss. I'll post some pics after the ss.

https://philcoradio.com/gallery2/1935a/#Model_16RX

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#2

Hello Terry,
That sounds Great Kirk does some nice work !
Far as the Logo you would think so because I can't think i ever have seen a Philco radio without a Logo somewhere .
Sincerely Richard
#3

Terry

Yes - between the tuning knobs and the escutcheon.

Remember, the dial is upside down, so the decal must also be placed "upside down" so that it is right side up when the dial and escutcheon are closest to you if the unit were sitting next to your easy chair.

--
Ron Ramirez
Ferdinand IN
#4

Tnx Ron,

I think Mr Huff's set must have the B or X dial in it. That's why his set is oriented backwards. It's confusing to look at if have one. Must have gotten the 1939-40 decal value pack [Image: https://philcoradio.com/phorum/images/sm...on_eek.gif] Not trying to make sport of Mr Huff but just some observations vs an original set would have.

Now that I think of it the dial is going to hard to read with that set up. It will at the far side and the dial is angled away from the viewer. Although the original seems awkward (dial closest to the operator) it makes sense now that way.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Very interesting! So, the 16RX chairside has a different dial than the rest of the 16 line?
#6

In the words of the late Nipsey Russell "Oh Yeah".
The 660L has the same style too where it's closer to the viewer.


Attached Files Image(s)
   

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 5872 online users. [Complete List]
» 1 Member(s) | 5871 Guest(s)
Avatar

>