1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Safety Cap Question
Phil27
Member
***
Posts: 66
Threads: 17
Joined: Dec 2020
City: Kingston State, Province, Country: Ontario
#1

10-19-2022, 03:36 PM
I know you should always use Safety caps when replacing certain Philco blocks that cross the AC line. 

My question is in regard to how specific do you have to be for values. The radio I have requires two .015 mfd caps in the bakelite block I need to replace. I have some .01’s and some .02’s . Can I use either of these in place of the .015’s. 

Justradios require a minimum order plus shipping and I really don’t need any other parts at this time.
Find
Phil27
Member
***
Posts: 66
Threads: 17
Joined: Dec 2020
City: Kingston State, Province, Country: Ontario
#2

10-19-2022, 03:52 PM
The .01’s and .02’s I’m hoping to use in place of the .015’s are safety caps. I should have mentioned that in my post.
Find
radiorich
Super Moderator
******
Posts: 1,732
Threads: 110
Joined: May 2008
City: Omak State, Province, Country: WA
#3

10-19-2022, 04:13 PM
Hello Phil27,
Either one would work just fine but .01ufd is what is normally used !

Sincerely Richard
Find
Phil27
Member
***
Posts: 66
Threads: 17
Joined: Dec 2020
City: Kingston State, Province, Country: Ontario
#4

10-19-2022, 09:39 PM
Thanks Richard.
Find
Arran
Phorum Expert
*****
Posts: 4,816
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#5

10-20-2022, 03:31 AM
I would use the .02 uf safety caps if you have them, it's better to go a little higher in value then too low. I'm surprised that you can't get .015 uf from Mouser or Digikey, though I do not think it'd critical.
Regards
Arran
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Mike; I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM
An attempt to remove the Field Coil from a G speaker
Arran Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM
An attempt to remove the Field Coil from a G speaker
Mike;  I would unwrap the field coil, and see if maybe there a break near one of the ends, like where the coil wire att...Arran — 10:23 PM
An attempt to remove the Field Coil from a G speaker
...and this is what I did. I fed a little LT into the screwholes with a small brush, and a little on the rim next to the...morzh — 09:52 PM
Philco 40-120C Restoration
I combined the two 40-120C threads together as we like to keep the discussion of the same radio together. It helps with...klondike98 — 09:36 PM
Philco 40-120C Weak, Distorted Ouput
Just checked were I buy tubes price is four dollars. So living in Florid we have a local source for tubes. David    David — 09:14 PM
Philco 40-120C Weak, Distorted Ouput
The higher voltage may be due to higher mains voltage. My mains run 120-125AC when the set was new mains would be 110-11...David — 09:09 PM
Philco 40-120C Weak, Distorted Ouput
Thank you for your reply. I pulled a speaker from a Philco 41-221 and received the same result. I used a signal tracer t...bluecap — 08:45 PM
Philco 40-120C Weak, Distorted Ouput
Have you tried a different speaker? How did you trace the distortion? How do you know it is weak? What is the reference?...morzh — 08:33 PM
Philco 46-480 Electronic Restoration
Amen to that! Every time I think I’ve captured them all, I realize that there’s another error. My goal is to finish with...jrblasde — 07:00 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration