1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 40-180 Volume
gdolph
Junior Member
**
Posts: 12
Threads: 1
Joined: Aug 2022
City: Calgary State, Province, Country: Alberta
#1

10-24-2022, 05:45 PM
I have a couple of Philco Model 40-180s that I have been working on. Both have been recapped and out-of-spec resistors replaced. My problem is that the maximum volume on both is not as loud as I would like. When I touch the top of the converter tube 6J8G (shows up as 7J7 in any schematic, as per production change run 4), volume improves dramatically for both. Any thoughts on what is causing this and how to make this volume improvement permanent?


Attached Files Image(s)
   
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
#2

10-24-2022, 07:17 PM
Hi and welcome to the Phorum,

I would check #13 the plate choke for the rf amp isn't open and that the loop ant is connected properly.

Here's the Philco service info for your set. https://philcoradio.com/library/download...20Book.pdf

GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 10-24-2022, 07:23 PM by Radioroslyn.)
Find
radiorich
Phorum Expert
*****
Posts: 1,472
Threads: 89
Joined: May 2008
City: Omak State, Province, Country: WA
#3

10-24-2022, 07:24 PM
Hello gdolph,
welcome aboard and I agree with terry and I would also Add they might need some alighment too !

Sincerely Richard
Find
morzh
Odobenus rosmarus
*****
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
#4

10-24-2022, 08:29 PM
I will second...third Terry's suggestion. Very typical symptom.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 10-24-2022, 08:30 PM by morzh.)
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration