Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

16B cabinet color
#1

The house of a recently deceased neighbor is being cleaned out and this kinda tired 16B was headed for the dumpster. I thought
I'd see what I could do with it and, with the amount of labor involved, I might as well do it right-  so here's my question: What
color were the dark parts of the cabinet, black or very dark brown? Was the finish meant to be opaque or was the grain meant
to show through? The cabinet was stripped long before I got it.
  One idle curiosity question too. I'm not used to seeing eight-sided knobs on Philco products. How long were they used and did
the whole product line get them or just some models?
   Sorry for asking questions you guys probably settled long ago.
-Dave


Attached Files Image(s)
   
#2

Hi Dave - a previous post on the colors for these cabinets: https://philcoradio.com/phorum/showthread.php?tid=8830
#3

Here's the link to our gallery photo as well:
https://philcoradio.com/gallery2/1935a/#Model_16B
#4

Hi Dave and welcome to the Phorum,

You found one of Philco's best table top sets. It's a beast! I have a couple of the them.
Here's a link to the 1st cabinet I did. https://philcoradio.com/phorum/showthread.php?tid=19986
It was stripped too. And broken. I ended up using
Mohawk Van Dyke Walnut M100-0353. I don't think it's as red as the extra dark walnut.
Also used a lot of sanding sealer. The hypo work wonders for doing the pinstriping.

I'll mention while your working on the cabinet be sure to check the joints. Loose joints
can cause splitting and cracking of the corner and top panels as it's a heavy set to pick
up by the rear arch.

As for the knobs I can't think of many sets that use them. Would have been around 1934
-35. Renovated Radios was making repos for all 3 of them.  And the grille cloth can be had
from Micheal Katz.

GL w/your new project!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Hello Dave and welcome to the Phorum! Terry wasn't kidding when he said "beast". Make sure the table you put it on is sturdy as well! The others showed you where to start, so I'll just say Good Luck! Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently no members online.

>