Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

16B cabinet color
#1

The house of a recently deceased neighbor is being cleaned out and this kinda tired 16B was headed for the dumpster. I thought
I'd see what I could do with it and, with the amount of labor involved, I might as well do it right-  so here's my question: What
color were the dark parts of the cabinet, black or very dark brown? Was the finish meant to be opaque or was the grain meant
to show through? The cabinet was stripped long before I got it.
  One idle curiosity question too. I'm not used to seeing eight-sided knobs on Philco products. How long were they used and did
the whole product line get them or just some models?
   Sorry for asking questions you guys probably settled long ago.
-Dave


Attached Files Image(s)
   
#2

Hi Dave - a previous post on the colors for these cabinets: https://philcoradio.com/phorum/showthread.php?tid=8830
#3

Here's the link to our gallery photo as well:
https://philcoradio.com/gallery2/1935a/#Model_16B
#4

Hi Dave and welcome to the Phorum,

You found one of Philco's best table top sets. It's a beast! I have a couple of the them.
Here's a link to the 1st cabinet I did. https://philcoradio.com/phorum/showthread.php?tid=19986
It was stripped too. And broken. I ended up using
Mohawk Van Dyke Walnut M100-0353. I don't think it's as red as the extra dark walnut.
Also used a lot of sanding sealer. The hypo work wonders for doing the pinstriping.

I'll mention while your working on the cabinet be sure to check the joints. Loose joints
can cause splitting and cracking of the corner and top panels as it's a heavy set to pick
up by the rear arch.

As for the knobs I can't think of many sets that use them. Would have been around 1934
-35. Renovated Radios was making repos for all 3 of them.  And the grille cloth can be had
from Micheal Katz.

GL w/your new project!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Hello Dave and welcome to the Phorum! Terry wasn't kidding when he said "beast". Make sure the table you put it on is sturdy as well! The others showed you where to start, so I'll just say Good Luck! Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Mike; I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM
An attempt to remove the Field Coil from a G speaker
Arran Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM
An attempt to remove the Field Coil from a G speaker
Mike;  I would unwrap the field coil, and see if maybe there a break near one of the ends, like where the coil wire att...Arran — 10:23 PM
An attempt to remove the Field Coil from a G speaker
...and this is what I did. I fed a little LT into the screwholes with a small brush, and a little on the rim next to the...morzh — 09:52 PM
Philco 40-120C Restoration
I combined the two 40-120C threads together as we like to keep the discussion of the same radio together. It helps with...klondike98 — 09:36 PM
Philco 40-120C Weak, Distorted Ouput
Just checked were I buy tubes price is four dollars. So living in Florid we have a local source for tubes. David    David — 09:14 PM
Philco 40-120C Weak, Distorted Ouput
The higher voltage may be due to higher mains voltage. My mains run 120-125AC when the set was new mains would be 110-11...David — 09:09 PM
Philco 40-120C Weak, Distorted Ouput
Thank you for your reply. I pulled a speaker from a Philco 41-221 and received the same result. I used a signal tracer t...bluecap — 08:45 PM
Philco 40-120C Weak, Distorted Ouput
Have you tried a different speaker? How did you trace the distortion? How do you know it is weak? What is the reference?...morzh — 08:33 PM
Philco 46-480 Electronic Restoration
Amen to that! Every time I think I’ve captured them all, I realize that there’s another error. My goal is to finish with...jrblasde — 07:00 PM

[-]
Who's Online
There are currently no members online.

>