Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Television - unknown model
#16

Lookin' good so far!! Wonder what would happen if you took to washing the grill cloth, it looks like that there is enough nicotine and tar on it to be positively carcinogenic!

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
Best Regards, 

MrFixr55
#17

I may try to give it a wash but to be honest I have had little success at washing these old grill cloths. In this case it’s almost invisible behind the wood grill and I do have some suitable replacement cloth so a wash might be worth a try.
#18

The washing worked out pretty well. Here's a before & after with the wash water in the middle. I used baby shampoo with warm water and very gentle movement of the cloth in the water for about 10 minutes. After washing I rinsed multiple times and then blotted it dry on paper towels and let it air dry. It could probably use another 10 min wash but I'm going to leave it where it is.

[Image: https://www.dropbox.com/s/eydr16icu2cpns....jpg?raw=1]
#19

That's an interesting pattern, considering that it is rather hidden behind a wooden grille. Wonder if they had i style for most of their radios with either an open face or a grilled face.

This is shaping up to being a real nice restoration!

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
Best Regards, 

MrFixr55
#20

The JB Weld filling the thread grooves for the knob set screw worked great. I retapped the threads without redrilling it. I also put in a slightly longer set screw so it would have an extra thread or two for grip. Set screw tightened down nicely. Thanks Gary, David and MrFixr.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2981 online users. [Complete List]
» 2 Member(s) | 2979 Guest(s)
AvatarAvatar

>