Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Antennas
#1

Hi guys. I've been MIA for a few years, moving house a couple times among other significant events keeping me from this hobby.

I listened to my Model 20 a fair amount during 2020 while working from home until the power stopped working. I finally had a look and discovered a poor original wire from the power switch. Replaced and it's back in business (except for an issue of occasional good signal that becomes poor and drops as the set warms up over a couple minutes. My original thought was a hot tube issue, but will start looking into it more this spring).

Now that I'm settled in a house, I'm thinking of improved reception for my radios. What do you guys think of a roof aerial or something mounted in the attic? I've used an assortment of plain wire antennas over the years that have been "ok", but would like better performance overall. I'm about 30 miles southwest of Chicago and can pick up a couple stations pretty well, but not much else. I'd like to listen to something besides the ballgame and political talk radio.

Greg

"We are here to laugh at the odds and live our lives so well that Death will tremble to take us."
#2

Quote:I'm thinking of improved reception for my radios. What do you guys think of a roof aerial or something mounted in the attic?
Good idea Icon_biggrin 

Give it a good ground too, short and direct to earth, not the ground for the wall outlet...

Chas

Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
#3

Quote:Give it a good ground too, short and direct to earth, not the ground for the wall outlet...

I figured I'd run a long wire to the basement and ground it to the water main from the city. It's copper and certainly underground!

Greg

"We are here to laugh at the odds and live our lives so well that Death will tremble to take us."
#4

Hi Greg, as for an antenna, I’ve had great results using my landline phone line. In most homes, there are 4 wires in the line coming in. 2 of them are fore the phone and the other 2 have nothing on them. I hooked a .001mfd cap to either one of those and run a wire to my radio. That gets me about 60’ or more of antenna running from the house, up high and out to the pole on the street plus the extra footage run throughout the house. And now since we’ve done away with our home phone, I can put my radio in any room in the house and have access to that antenna from any phone Jack.

Ron

Bendix 0626.      RCA 8BX5.   RCA T64
Philco 41-250.    Philco49-500
GE 201.             Philco 39-25
Motorola 61X13. Philco 46-42        Crosley 52TQ
Philco 37-116.    Philco 70
AK 35                Philco 46-350
Philco 620B.       Zenith Transoceanic B-600
Philco 60B.         Majestic 50
Philco 52-944.    AK 84




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1040 online users. [Complete List]
» 1 Member(s) | 1039 Guest(s)
Avatar

>