Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco 15 x grille cloth
#1

just purchased a philco 15 x in really nice origional condition but grill clothe is showing wear.does any one know which pattern of cloth is most like the origional
#2

Pattern 40 from Radio Grille Cloth Headquarters is about as close to the original as you are going to get. Not exactly the same, but close:

http://www.grillecloth.com/

--
Ron Ramirez
Ferdinand IN
#3

thanks Ron i will get that one
#4

Older Philco consoles can be "spruced up" nicely by using a velvet elvis painting for the grillecloth. I installed tiny black lights above the elvis painting grillecloth on my otherwise drab Philco model 201X to highlight the glow in the dark paint. It looks exxxxcelent......
#5

i am sure that is a dazzling and interesting look and i too am a elvis fan but i wanted the look of 1933 in this classic console.
#6

Another way to improve the looks of them is to affix baseball card stickers, post office wanted posters, or refrigerator magnets to the cabinet. Maybe a good way to realize the 1933 look would be to decoupage 1933 newspaper articles to the cabinet???

P.S. Don't take ANY of what I said seriously! BUT believe me, I have seen some awful things done to an otherwise nice radio for only God knows why. The one that I think appalled nearly all of us here was the fellow on eBay that dismantled a Philco 116B non shouldered tombstone cabinet and sold the cabinet and chassis parts. Oy vay !!!!

The 15X is a set that I would love to have someday! Good luck with it!
#7

yeah... cabinet parts.


Quote:shipping is too expansive so I destroyed this otherwise perfectly preserved rare radio to prevent any interested buyers to pay me for shipping it. Maybe the parts will sell off?

If I recall he sold the tubes and that's about it.

-Mars
#8

the previous owner removed most of the tubes from this one i found one in the socket and two 37 loose on top of the chassis and they tried to connect a rca jack and unhooked the big speaker and tried to connect a external speaker. luckly no permanent damage to anything.i would like to clean and keep the origional grille cloth but this is fading and worn to the point where i want to see what a new one looks like. the origional finish is still very presentable.found this one at a auction and there was little interest in it.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>