Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

cool 20s Philco
#1

I saw this cool 20s Philco online awhile back, and I love it. The guy got cold feet about selling it, but I sure would have bought it Icon_smile
I think it is a 1929 model or so. Quite nice indeed.

Note from site admin: Sorry, but the photo which was attached to this post is no longer available.

**I survived because I was tougher than everybody else**

--Bette Davis
#2

Actually, it's from 1933. This appears to be the same cabinet as my 91D:

[Image: http://i326.photobucket.com/albums/k420/...F/91Da.jpg]

Only, the set in your photo appears to have had its doors removed. So maybe it's just as well that you did not get it.

The one in your photo is probably a 14D, 17D or 18D due to the wider spacing between the lower three knobs.

This 91D is a set I bought from someone in Louisville a couple months back, and I took the photo shortly after I brought it home. I still have not done anything with it. And, yes, the blue cloth will get replaced eventually with something more suitable.

--
Ron Ramirez
Ferdinand IN
#3

Looks really nice Ron. Does it play?

tractorforum.com *** I reserve the right to be wrong
#4

No, it does not (yet). I brought it home...I put it in the kitchen to replace a 118D I recently sold...that's as far as I have gone with it. I'll get to it eventually. Icon_smile

--
Ron Ramirez
Ferdinand IN
#5

Too bad about the "weekend warrior" finish on that 91D, I hate having to undo cruddy workmanship like that. Is it missing veneer above the control panel/doors, the other cabinet has some wavy grained veneer in that area?
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 1708 online users. [Complete List]
» 1 Member(s) | 1707 Guest(s)
Avatar

>