Philco 46-1213 Power Consumption
Posts: 7
Threads: 2
Joined: Mar 2022
City: Richardson
State, Province, Country: TX
Hello all,
I have a 46-1213 that should be drawing 125 watts. It is drawing a little high, 130 or so depending on if a station is tuned or not. A strong signal lowers the watts to 120 or so. Is that normal? I have not noticed a radio doing that before.
Second question, turning on the the phono, the power consumption up to 170-175 watts.
Does this sound normal? What causes this behavior if it is not normal?
Thanks.
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hi and welcome to the Phorum,
Wouldn't be concerned about the extra 5 wts of power.
The reason for the variance in the wattage when tuning in a strong station vs a weak one is that the avc circuit is biasing the gain of the rf and IF tubes down to keep the volume even. This in turn lowers the plate current of these tubes thus dropping the total power consumption.
I'm not all together sure where the 175w number comes from. Is it just the radio chassis or the radio and phono?
This number comes from a brand-new chassis with all new everything. How does your chassis stack up to that?
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
I put my 46-1213 through a Kill-a-Watt and it is 60W (shows 0.06kW). Without the phono, but my phono is a VOM, not the original. I tuned the local station. The volume did not make much difference (it shows kW so it would not notice it).
https://www.philcoradio.com/phorum/showt...?tid=21963
This is my thread on my radio.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 10-11-2023, 10:08 AM by morzh.)
Posts: 7
Threads: 2
Joined: Mar 2022
City: Richardson
State, Province, Country: TX
Thanks guys,
Radiorosyln,
I wasn't very clear in my second question, sorry. The 175 watts comes from just pressing the phono button, turning off the FM or AM radio and running the turn table, so I think it is bypassing the radio sections and just running the turntable and power section of the radio. The radio is in good shape, with all electrolytic and paper capacitors changed, which was quite a lot of them. I finished tracing the schematic looking for any mistakes I may have done and all seems fine. That's when I asked the forum for help, mainly on the phono watts consumption.
Morph,
I am familiar with your thread. The wattage changes tuning the signal strength, not the station volume. I have a Kil-o-watt meter somewhere, I'll check consumption with it. I am reading watts on a Sencore PR-57.
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Well, what you have not told us is this:
1. Has the radio been recapped? Does it work?
2. Does the radio play the records when you use your turntable?
3. Has the turntable been gone through?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 7
Threads: 2
Joined: Mar 2022
City: Richardson
State, Province, Country: TX
Yes, it has been recapped and out of spec resistors have been changed. The radio works OK, has a slight hum in FM but FM works, gets AM and SW. It could be louder, but OK.
The phono arm was stuck and I freed it up, greased and oiled everything and have a new needle in it. The controls are not right but it spins the platter so I can test it.
I finally got the phono to play through the radio faintly, and it seems the speed is OK. I guess it could be straining to play at speed, which would cause the power consumption to go up I would think. I will check that.
I hope that answers your questions.
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Faintly: you do use the transformer that is in the back, right? And the pickup is original, EM type?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 7
Threads: 2
Joined: Mar 2022
City: Richardson
State, Province, Country: TX
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Shadow Meter Bulb
|
| Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM |
|
Philco 41-608 changer coupler
|
| 3D-printing...short of machining, of course.
Or molding.morzh — 05:20 PM |
|
Philco 41-608 changer coupler
|
| Thanks, Morzh.
That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM |
|
12' Philco
|
| If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel.
Kareem would have an e...morzh — 01:48 PM |
|
12' Philco
|
| And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM |
|
Hickok AC51 tube tester
|
| I think they have only shown the secondaries of the transformer.
Two of them feed the rectifiers' filaments.morzh — 12:58 PM |
|
IF can wire size and Rubber mounts?
|
| Arran
If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM |
|
12' Philco
|
| Rod,
Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently.
H...morzh — 12:54 PM |
|
Hickok AC51 tube tester
|
| Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM |
|
IF can wire size and Rubber mounts?
|
| Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM |
|
Who's Online
|
There are currently 5844 online users. [Complete List]
» 1 Member(s) | 5843 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
