Posts: 5
Threads: 2
Joined: Sep 2017
City: Johnstown, PA
I have an 87 that I rebuilt several years ago that worked great. Never aligned it as the reception was very good. However, one day when it was on I heard some loud popping noises. At first thought it was electrical interference since it was still playing. After a few minutes, the popping suddenly got louder and more constant, the music died. When up to find an 80 tube pinkish/purple with fireworks inside the tube. So replaced the 80 as it was showing shorts. Reception now very poor. Found and replaced two bad 26's and the 27. Helped but not much. Went over the radio again, all caps & resistors, tubes showing good, good voltages. I've decided to check the alignment now to see where that is. Following the document here on philcoradio, "Neutralization of Philco Neutrodyne-Plus Receivers" I've been able to improve reception, but not to where it was in the past. In that document, it has the following statement:
>>> Adjust the 3rd neutralization condenser (number 6 in Figure 2) for minimum signal. <<<
What exactly is minimum signal? If by meter, is this when it's at '0'? If by listening to the speaker, when the signal generator tone is no longer heard? The process has improved reception, but not close to where I think it should be at this point, and I'm thinking my interpretation of minimum signal may be incorrect.
Any thoughts on this or something I may be missing, please let me know. Thanks!
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
https://philcoradio.com/library/index.ph...receivers/
Probably the best description of minimum signal is at it's lowest point. The 87 has no avc so you can dump a whole lot of signal into it if you need to.
Got an 87 myself, it's a heavy brute!
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 15,837
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
>>min·i·mum
/ˈminəməm/
noun
noun: minimum; plural noun: minima; plural noun: minimums
the least or smallest amount or quantity possible, attainable, or required.
So, there it is. It is the minimal value you could achieve. Say, from 10V, 5V, 4V, 5V, 7V sequence the value of 4V would be the minimum.
Are you using a dud to neutralize?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 12-11-2023, 10:16 PM by morzh.)
Posts: 5
Threads: 2
Joined: Sep 2017
City: Johnstown, PA
Yes, using a dud. However, I don't know if it's too much of a dud. . . It was good at one time, but has a dead filament now. After reading some of the documentation, if it has problems outside of the dead filament it's not good to use. So this weekend I'll make the adapter to change a good tube to a dud tube.
Posts: 15,837
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
It is unlikely the tube has more than one problem.
If the filament opened, the tube is likely a good dud.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 696
Threads: 8
Joined: Apr 2018
City: S. Dartmouth
State, Province, Country: MA
Quote:So this weekend I'll make the adapter to change a good tube to a dud tube
Use the tube with an open filament or take a tube that has too low an emission and cut off one of the filament pins.
Creating an adapter will add a few pf to the circuit, that will affect the neutralization such that it will not be null when the good tube is reinstalled...
Watching a meter will only distract when neutralizing. The ear is ample enough instrument and no leads be connected.
Theoretically, forcing a strong signal to neutralize may not be a good idea as Miller effect may come into play and cause an error. Be sure all shields are in place and any bottom plate too.
If the set had a tendency to oscillate in one area of the band, note that area and neutralize at that frequency. If the area of oscillation has moved and set still oscillates split the difference in the neutralizing frequencies and try a third time.
If still no joy then component placement, RF tube(s), voltages, grounds or wiring may be an issue, hopefully not as they are even more "cut and try".
GL
Chas
Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
Posts: 1,034
Threads: 9
Joined: Jul 2020
City: Greenlawn
State, Province, Country: NY
I am a little worried as to why you had a fireworks display in the 80. This usually occurs only when their is a short across the power supply or in the power supply, usually a shorted filter cap.
You may be able to tape the filament lead of the tube that you actually intend to use in the set after neutralization, and then neutralize the set on that tube. When the neutralization is complete, remove the tape.
"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
Best Regards,
MrFixr55
Posts: 15,837
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
Was the fireworks around any festive holiday? That could explain why.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 1,034
Threads: 9
Joined: Jul 2020
City: Greenlawn
State, Province, Country: NY
"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
Best Regards,
MrFixr55
Posts: 997
Threads: 40
Joined: Feb 2015
City: Roseville, MN
Posts: 24
Threads: 6
Joined: Dec 2019
City: Schererville
State, Province, Country: Indiana
Make sure all your RF coils are good and no open primary windings.
Good luck
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
Made mistake & did not label connection
|
| Hi John,
I don't have this radio, but I can supply some info:
Based on your pic, pins 7,8 and 1 are used together, go...MrFixr55 — 02:02 PM |
|
New Philco Repair Bench
|
| As far as I know, the Repairbench does not work, and has not been working in a while.
Chuck (we had that campaign looki...morzh — 01:33 PM |
|
Radio city products 664 schematic request
|
| Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM |
|
New Philco Repair Bench
|
| Thanks Gary.dconant — 12:16 PM |
|
New Philco Repair Bench
|
| I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM |
|
New Philco Repair Bench
|
| I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM |
|
Made mistake & did not label connection
|
| It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires.
Why'n't you...morzh — 09:49 PM |
|
Made mistake & did not label connection
|
| I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM |
|
Made mistake & did not label connection
|
| You'll have to forgive me, I am not sure what you mean. Can you explain what you are really saying. If anyone does not...georgetownjohn — 08:05 PM |
|
Made mistake & did not label connection
|
| Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM |
|
Who's Online
|
There are currently 3740 online users. [Complete List]
» 4 Member(s) | 3736 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
