1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
philco model D-664
retired2020
Junior Member
**
Posts: 12
Threads: 4
Joined: Feb 2021
City: middletown State, Province, Country: Delaware
#1

01-21-2024, 05:31 PM
restoring this portable radio D664 

Before restoration turned it on and got lots of noise but no stations. Assumed eletrolytics  were bad as well as old selenium rectifier since it only put  out 107 volts not 125  as shown on schemo . Also  replaced paper capacitors, and c4 , 3 and 7 . All tubes tested and Okay. tested all resisters and okay.  Same issue and voltage at diode not any higher. While  all tubes were good at startup noticed that  IU4 was glowing brightly , so tested  all tubes IU4 and IU5  are now NG  . Before  replacing tubes powered up without them .Only got 9 V dc at Diode  output but  -151 V DC at pin 1 on IU4 .Also  noticed same voltage on the socket tab that connects to the IU4  heat shield . Any suggestions helpful


Attached Files
.pdf d 664 schemo.pdf Size: 947.44 KB  Downloads: 142
Find
klondike98
Phorum Moderator
******
Posts: 5,162
Threads: 273
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

01-21-2024, 06:37 PM
Moved this thread over to the Electronic Restoration section.

Just a thought… double check your cap and other replacement wiring. I’ve mis-wired more than once and had to back track to sort it out.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2625 online users. [Complete List]
» 2 Member(s) | 2623 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration