Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Unusual High Boy console
#16

Please do take additional detailed photos, and keep us informed on progress. It would be nice to know the tube line-up. Joe

Joe

Matthew 16:26 "For what does it profit a man if he gain the whole world, yet lose his own soul?"
#17

The rolled up paper above the metal ID plate may have some info. Looking forward to more pictures. David
#18

If you'd like to bone up on the 16's here's a good start. https://www.tuberadioland.com/philco16L_main.html

The tabletop sets (B's) and the consoles use the same chassis except for the power transformer, rectifier tube, and speaker. Console sets are larger. Something else that Philco employed in their 1933/34 sets was inter station noise suppression (aka qavc). That's what the switch on the right side of the cabinet turns off and on. There's a control shaft on the back of the chassis that sets the level.

I have one on the bench (the chassis done) in limbo as I need to finish up the cabinet. And a couple of others too. There are a plethora of folks here that are well versed in the workings of Philco sets. Drop by if you have any questions.

Here's a thread I started several yrs ago. https://philcoradio.com/phorum/showthread.php?tid=20055
Cabinet https://philcoradio.com/phorum/showthread.php?tid=19986

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#19

Terry

I have never said it was 14 or 18; I merely pointed to the escutcheon as the one used in those, and then answered the escutcheon question.
Now that I see the chassis, I see it is a Philco, that is without doubt.

I suspect it could be 16 / 18 modification for a non-US market, due to the combination of the holes in the chassis, the speaker plug and the capacitive filter can.
In fact the label says 18T.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3407 online users. [Complete List]
» 2 Member(s) | 3405 Guest(s)
AvatarAvatar

>