Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-2
#1

Hello, I just picked up a Philco 38-2. It will probably be a while before I dig into it. What kind of problems am I likely to run into with the 11 tube console. It has a Magnetic Tuning switch. What does that do?

Dan
#2

If I'm not mistaken the Philco magnetic tuning was another name for AFC. See: https://www.tuberadioland.com/automatic_...d_AFC.html

Here's the Philco service bulletin for this model: https://philcoradio.com/library/download...l.%202.pdf
#3

Thanks for the link Bob.
#4

I go in to the chassis presuming all caps (mica excluded) are bad, and all resistors have probably drifted. I replace all the caps and resistors. They are the relatively inexpensive compared to what they can take out. Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#5

My approach is to check out the electronics and see if there is anything that may prevent the radio from functioning properly then check out the cabinet and do cabinet repairs first.

Chassis:
Check all coils for continuity and record their resistance on the schematic. Any coil that is open will have to be rewound or replaced. Test all resistors for value within ten percent. Identify them on your list or the schematic. Identify the electrolytic and paper/wax capacitors and put them on your list. Check condition of the speaker.

Order parts. While the parts are coming get that cabinet work done. Make it beautiful again. Then do the chassis and make your beautiful cabinet sing.
#6

Thanks Rob and Gary. That is pretty much what I do. I was wondering if there were any problem spots with the radio.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2629 online users. [Complete List]
» 2 Member(s) | 2627 Guest(s)
AvatarAvatar

>