1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 42-380 antenna hookups?
TomasTomas
Junior Member
**
Posts: 5
Threads: 3
Joined: Apr 2023
City: Manhattan State, Province, Country: NY
#1

06-19-2024, 03:05 AM
There are four screws on the back to run the 3 antenna wires to.  Two of the wires are paired together, the third one is not.  Question: Which wire goes where?  Looking at this model on the net, people have it connected in different ways.  Looking from the back, I have seen the two paired ones connected in the middle, then others to the left, others to the right.  Help!  Icon_crazy        
(This post was last modified: 06-19-2024, 03:06 AM by TomasTomas.)
Find
morzh
Odobenus rosmarus
*****
Posts: 15,823
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#2

06-19-2024, 09:46 PM
Typically one is GND, one is balanced (2 wires) and one is unbalanced (single ended).
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
TomasTomas
Junior Member
**
Posts: 5
Threads: 3
Joined: Apr 2023
City: Manhattan State, Province, Country: NY
#3

06-20-2024, 01:29 AM
That information doesn't address my problem as the connections are not marked, and as stated I have seen different combinations hookups on the net. They all can't be correct. Just need to know what antenna wires go to which screw.
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

06-20-2024, 09:09 AM
Your set the screw terminals connect only to the loop ants barring the one test point. You need the external ant adapter. It plugs into the socket above the terminal strip. It has a connection for a single wire ant.

https://philcoradio.com/library/download...20Book.pdf
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
TomasTomas
Junior Member
**
Posts: 5
Threads: 3
Joined: Apr 2023
City: Manhattan State, Province, Country: NY
#5

06-20-2024, 01:56 PM
Pulls in stations, so no additional ant required. Just need correct wire hookup sequence.

Thx
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3831 online users. [Complete List]
» 1 Member(s) | 3830 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration