1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Coronado 962A
RodB
Phorum Expert
*****
Posts: 1,120
Threads: 44
Joined: Feb 2015
City: Roseville, MN
#1

07-17-2024, 11:25 AM
I'm looking at replacing an output transformer for this farm radio. It has 2 1Q5s in parallel driving a SE OPT. The 1Q5 has a suggested plate load of 8k. If the tubes are in parallel then can I be okay using an OPT with a 4K primary impedance?
(This post was last modified: 07-17-2024, 12:44 PM by RodB.)
Find
Arran
Phorum Expert
*****
Posts: 4,862
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#2

07-17-2024, 05:10 PM
Just out of curiosity is there an economy switch that shuts off one of the 1Q5 tubes to save on battery life? I couldn't find a 962A on N.A only a 962 so I assume it's similar. I think you would be right about the plate load impedance being 4000 Ohms, but I'm sure someone else will chime in.
Regards
Arran
Find
RodB
Phorum Expert
*****
Posts: 1,120
Threads: 44
Joined: Feb 2015
City: Roseville, MN
#3

07-17-2024, 05:20 PM
There doesn't seem to be a switch to turn off one of the 1Q5s. The schematic at NA is the correct one. The A suffix is for speaker size as noted in the schematic.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)