1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Resistor Advice Needed For A 1936 Philco 650
Tonym4704
Junior Member
**
Posts: 9
Threads: 5
Joined: Jun 2024
City: Shirley State, Province, Country: MA
#1

07-24-2024, 03:31 AM
Hello Everyone,
 I need advice regarding resistor replacement in a 1936 Philco 650 chassis that I am restoring. Most of the resistors in this radio are out of tolerance and check much lower than specifications. The Rider's schematic does not list any wattage ratings. Are 1/2 watt carbon composition resistors adequate to use throughout? Several of the resistors are dimensionally very large. Any advice or recommendations would be appreciated. Below is a link to the schematic. Thank you.
Tony

http://www.nostalgiaair.org/PagesByModel...013824.pdf
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

07-24-2024, 05:57 AM
https://philcoradio.com/library/index.ph...resistors/
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
Carl Travis
Member
***
Posts: 205
Threads: 6
Joined: Jun 2006
City: Moundsville State, Province, Country: WV
#3

07-24-2024, 06:07 AM
Tony,
Looks like Terry has you covered.
If you email me at the address I PM'd you with, I'll email you the parts price list with values.
Carl
Northern Panhandle, WV
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration