Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA WV-98c
#16

Two things.

1. Make sure your switch is clean and provide good contact across all ranges. It is S2 Range switch.
2. I don't think this is it (I think only the lower dual triode is involved for DC, as for everything else), but just in case, have the tubes been checked?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#17

Tubes and resistors are fine. R22 measures 9k so iam not sure if that could be the issue.
#18

Switch. Check the switch. Make sure it makes good contacts. Clean if necessary, Deoxit D or any contact cleaner (be careful and don't spray it all around).

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#19

I cleaned and checked the sw2 switch, its fine. Has to be something in the .5v to 15v circuit. Iam going to check the ac operation.
#20

No ac function. Pegs the meter to the left, no adjustment.
#21

If I had it in front of me, I would triy to trace the signal on one of the non-working functions.
Try to trace and highlite at least one non-working path.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#22

At this point, there is no input, just internal voltages
Which are incorrect and not sure what they should be.
#23

Those will probably depend on teh switch combination.

Could you list some that you see, their values and what they should be (if you know correct values)?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#24

Check out this crazy zero pot operation. Touching it drives it crazy. Its rubber tipped. Also the 6al5 has no negative voltage on it.
https://www.dropbox.com/scl/fi/gnvltn9la...fvikk&dl=0
#25

If this is R22, check the voltage on the wiper (86V).
If this is R33, see if the lower pin indeed connected to GND, the wiper is indeed wipes, and if the pot is OK.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#26

I measured the wiper of r22 , 95vdc.
#27

The resistor you are touching at the video, is it R22 or R33?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#28

R22, but it doesnt do that all the time. Strange. What do you think of the 95 voltage. I guess its close.
#29

Yes, it is close. It is a solid state diode rectifier, so the voltage won't depend much on the load, as would with tube rectifier.
However the behavior is strange.
Also, see if this pot,s case (and so the shaft) should be grounded through the fron panel, and somehow it is not.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#30

Case and shaft go to case. Center wiper of r22 has 3kohms to case.




Users browsing this thread: 23 Guest(s)
[-]
Recent Posts
Philco 37-S650X Face lift
Hello Stanley, that looks great !! Hey if you want you can come over to my house and restore my cabinet for my General...radiorich — 11:33 PM
Philco 37-S650X Face lift
I finished a facelift on this radio and I think it turned out pretty well.   It had at least 4 different woods on it....Stanleyii — 10:46 PM
Philco 37-2650X Face Lift
Yep, that would be a better place for it. Didn't know there was a category there. Is there a way to move it out just s...Stanleyii — 10:34 PM
Philco 37-2650X Face Lift
Excellent job! Would be a bit better to place the topic to the "Cabinet Restoration" section.morzh — 10:14 PM
Model 96 cabinet veneer
I am almost positive it is white or light walnut. Then stained or toned to the proper color. Dickmadsowry — 09:58 PM
[split] Newbie questions RE: Philco 41-608
Does the cap pair #61 (input filter) have its centerpoint to teh chassis? Actually, has the radio been fully re-cappe...morzh — 09:51 PM
[split] Newbie questions RE: Philco 41-608
Gary Thank you. Toddtmurphy — 09:14 PM
[split] Newbie questions RE: Philco 41-608
I agree with Morzh. I've split this issue to it's own thread. Take care and BE HEALTHY! GaryGarySP — 09:03 PM
Newbie questions RE: Philco 41-608
John Thank you for the detailed response. I checked my connection again based on the schematic and your suggestions....tmurphy — 08:42 PM
Philco 38-2 Low Volume
Hi MrFixr55, The aux sound was good and yes it can be made too loud. The tone has no real effect on volume just tone, ge...dconant — 06:04 PM

[-]
Who's Online
There are currently 1601 online users. [Complete List]
» 1 Member(s) | 1600 Guest(s)
Avatar

>