1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 610B Tone Control 30-4318 caps
Ken Kidd
Junior Member
**
Posts: 16
Threads: 6
Joined: Apr 2011
City: Morgantown WV
#1

10-12-2011, 11:26 AM
Hi all, Have some conflicting info on the cap values for this tone control. Both my Philco schematics(one early and one later production) list .01 and .02. I have Ray's original "Philco Condensers and More" ( Great resource book!!!) which lists a .02 and a .003 for this tone control. The Philco Repair Bench does not list this tone control. Does anyone know which would be the correct ones? I'm assuming the .02 value is correct. Thanks-Ken
Find
Texasrocker
Phorum Expert
*****
Posts: 909
Threads: 117
Joined: Jun 2007
#2

10-12-2011, 02:37 PM
Those caps aren't that critical, either combination will work. Use what you have, just follow correct layout (placement). Yes, the Philco Condensers and More book is nice to have!! Best of luck with your restoration.
Find
Ken Kidd
Junior Member
**
Posts: 16
Threads: 6
Joined: Apr 2011
City: Morgantown WV
#3

10-12-2011, 02:56 PM
Thanks for the input. Will probably go with whats listed in the Philco schematic-Ken
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,305
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
#4

10-12-2011, 09:01 PM
Go with to .003 and .02. That will give you a fair amount of difference between the two setting.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#5

10-12-2011, 11:01 PM
Yes, agree with Terry, .003 and .02 are a good combination for steps in tone.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 37-116 Cabinet Repair
It looks to me like the structure under the veneer may have expanded from humidity cracking the veneer on the surface. W...Arran — 09:42 PM
Help with Supreme 599
Iam only getting 4vac out of the tranny For the 80 filament. The line rheostat Looks fine and the tranny is getting 11...daveone23 — 08:45 PM
Rogers Majestic R-646
Transformers rewind? It's very easy! If you don't have round eyes  8-) Vlad95 — 01:55 PM
Help with Supreme 599
I found a broken wire from the end og the 300 ohm line adjust to the transforner but i dont think its needed. The transf...daveone23 — 11:43 AM
Philco 38-10 Tuning Condenser
RodB I have been using pure Vaseline for a long time for thick lubrication of home radio devices. The main reason is t...Vlad95 — 10:58 AM
Philco 38-10 Tuning Condenser
Vlad, your comment about Vaseline brought a thought. Does anyone know the long term affect on using silicon grease on t...RodB — 10:34 AM
Philco 42-345 Restoration/Repair
Arran, didn't notice the specifics for the caps. What's the code going to get me? I'm working on restoring a Philco 50-9...RodB — 10:26 AM
Philco 38-10 Tuning Condenser
I managed to get the gears lined up and the springs back in. Much easier than it thought. Putting a thin wire down insid...dconant — 09:52 AM
Philco 42-345 Restoration/Repair
Rod, Mrfixr55 and everyone else thank you very much for all your help with this radio thus far. Today will be more testi...osanders0311 — 09:26 AM
Philco 38-10 Tuning Condenser
Thanks for the reply Vlad95. I can't even see the balls let along try to remove them. The grounding forks are going to p...dconant — 08:03 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration