Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

volume control
#1

Can someone tell me the resistance of a philco 7439 volume control.
#2

If it is for the model 80 it's 20K. Two quick checks, one unplug set turn volume all the way up. Measure resistance from ANT post to chassis ground. Should be very low like a few ohms. If not antenna coil primary is open. Two, Turn volume all the away down.Measure resistance from antenna post to chassis ground. Should read about 20,000 ohms. If not check volume control, open or bad ground connection.
How's your oscillator doing?
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

What model Philco are you working on?

I didn't see any data on your part number on Philcorepairbench.com.

-Keith
#4

Terry is correct, it is 20K. Part no. 7439 was used in model 80 and the three-knob 81.

--
Ron Ramirez
Ferdinand IN
#5

Do I get a prize????
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Yeah - a Philco 84B that needs complete restoration. Icon_twisted Icon_lol

--
Ron Ramirez
Ferdinand IN
#7

I unsoldered one outer lug, not the one to ground and measured it like a resistor, 17 ohms.
Strange, then I unsoldered the center lug and it read 27k. I thought you can measure a pot like a resistor if one of the outer lugs is disconnected.
#8

Depending on the circuit this may not be true, IE this case. However if the wiper is all the way toward the still connected end you should be able to get an accurate reading. Then you could connect the ohmmeter between the center and unconnected end and sweep it, and you will then see if there are any open spots.
#9

It also maybe effected by the very low resistance of the antenna coil connected to the wiper and ground.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco Model 71B
Is the arch area on the front of a Model 20 real or photo?MrFixr55 — 07:31 PM
Eico 584 schematic
Anyone have a schematic for this tester?daveone23 — 05:48 PM
Philco Model 71B
Good one!!! No if I go for it, I’ll fix it right lolslford310 — 04:38 PM
Philco Model 71B
Stucco on the arch?RodB — 04:31 PM
Philco Model 76 Highboy
Back in Feb I scored a nice model 95 Highboy, see earlier post.  Saved from a guy that likes chopping them up into Liquo...slford310 — 09:49 AM
Philco Model 71B
Adding a pic from the other side and the inside.  It will be a bit of work and a challenge but that's what makes it fun....slford310 — 09:32 AM
Philco 89B code 123 newbie
Hi Kurt Welcome to the Philco Phorum. Lots of phriendly pholks (see a pattern here?) who are happy to help.  Keep posti...MrFixr55 — 08:36 AM
Philco 89B code 123 newbie
Hello Kurt, Welcome aboard and you have a nice set to start on ! Yes, the bakelite blocks and I too find them fairly...radiorich — 07:12 AM
Philco 89B code 123 newbie
Getting started on my first Philco here, done some research and hopefully I now know enough to be dangerous.  :) Overal...Kurt P — 01:44 AM
Delco car radio Peko vibrator converstion issues
Richard, I reviewed the Panasonic specification sheets for this type capacitor and though dV/dt is discussed, there a...Chas — 11:48 AM

[-]
Who's Online
There are currently no members online.

>