Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Phuilco 41-280 / The Chassis is worse than I had expected
#16

Texasrocker Wrote:<<< snip >>> I just replied to a email from Rob in regards to restoring his 41-280. I am about 200 miles west of the DFW area, but will be happy to handle the full electronic restoration of this radio if Rob decides to proceed.

Yep, I got a quick and comprehensive response from Texasrocker... I'm feeling better about this little project with each passing day!

Well, except for all the hand sanding... sigh...

Texasrocker Wrote:I lived in the Dallas for many years, but relocated out of the traffic many yrs ago.

Man, oh man, you gotta respect judgment this good! Icon_lol
#17

Yeah Rob, I sure miss all my ol' friends in the DFW areas. Loved living there in my younger years for sure. I remember fighting the traffic for about 18 yrs. in the DFW areas. KRLD & KLIF are still two of my favorite stations! Nowadays, just before sun up,I turn on my 1936 Truetone D-723 with a longwire antenna outside my window and listen to the KRLD traffic reports from 200 miles away out here in the country. I remember being stranded in those traffic jams all too well. My wife also remembers. We just look at each other and say, "yep", been there, done that, and got the T-Shirt. Living in Austin for several yrs wasn't much better on the traffic situations either! Icon_lol




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently 3028 online users. [Complete List]
» 2 Member(s) | 3026 Guest(s)
AvatarAvatar

>