1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Texasrocker are you out there? Another cap question.
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#1

11-12-2011, 09:52 PM
I know you have some reference which is better than that posted on the work bench. Another one of those dang philco bakelite stuff caps I can't find a reference to. Its a 3903AB. I know it has one cap in it, can you tell me what it is? Add another as an edit, the 3903T. Single cap, what is it? One more, not on the bench list, a 7025D. Any help appreciated.

Thanks Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#2

11-13-2011, 01:11 AM
3903AB= 3903OSU
ONE ,01 UF 600V
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#3

11-13-2011, 01:13 AM
3903T = 39030SU
ONE .01 UF 600V
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#4

11-13-2011, 01:15 AM
SERVICE BULLETIN NO. 289
Is where I found the info
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#5

11-13-2011, 01:19 AM
no 7025D

but
7625D
3-4 .015 uf 600v
1-5 .006 uf 600v
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#6

11-13-2011, 03:56 PM
Thanks TROG, got me off and running again. Will have to check on the 7025D, perhaps I missread it and it was a 7625D.

Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
Texasrocker
Phorum Expert
*****
Posts: 909
Threads: 117
Joined: Jun 2007
#7

11-16-2011, 12:41 PM
Sorry for the delay getting here Jerry. Been real busy lately. Looks like you have the specific caps info you needed now. Always glad to help if I can, you can also pm me, as I'm not on the forums each and every day.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration